Contenu du fichier
/var/spool/fax/etc/config.ttyS1 : #
$Id: class1,v 1.3 2001/02/05 06:32:55 darren Exp $
#
# HylaFAX Facsimile
Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996
Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
#
publicity relating to the software without the specific, prior written
# permission
of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS"
AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING
WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
#
#
#
IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL,
INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES
WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT
ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY,
ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS
SOFTWARE.
#
# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION
TO REFLECT YOUR SETUP
#
CountryCode:
33 AreaCode:
0 FAXNumber:
+0123456789
(Mettre
ici votre numéro de fax) LongDistancePrefix:
0 InternationalPrefix:
00 DialStringRules:
etc/dialrules ServerTracing:
1 SessionTracing:
11 RecvFileMode:
0600 LogFileMode:
0600 DeviceMode:
0600 RingsBeforeAnswer:
1
(Mettre
ici le nombre de sonneries avant que le modem ne prenne la ligne lors de la réception
d'un appel) SpeakerVolume:
MEDIUM
(Le
HP sera coupé lorsque la connexion sera établie. Pratique pour entendre le modem
numéroter) GettyArgs:
"-h %l dx_%s" LocalIdentifier:
"Linux"
(Mettre
ici l'identification de votre station. 20 carac) TagLineFont:
etc/lutRS18.pcf TagLineFormat:
"From %%l|%c|Page %%P of %%T" MaxRecvPages:
25
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:
Class1 # use this to supply a hint
ModemRate: 19200
# rate for DCE-DTE communication (Vitesse
du port série en mode fax)
ModemFlowControl:
xonxoff
# XON/XOFF flow control assumed (Type
de contrôle de flux utilisé. Dans notre cas, logiciel)
#
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd:
AT&C1 # setup so DCD follows carrier
#GettyArgs: "-h %l dx_%s" #
modem must auto-detect fax/data
#
Pour que Hylafax route l'appel en fonction de son type, les fax vers le
# "demon" de fax et les données vers "mgetty"),
#
il suffit de rajouter au fichier de configuration:
# ModemSetupAACmd: AT+FCLASS=0;+FAE=1
# ModemAnswerFaxBeginCmd: "<waitfor:CONNECT><waitfor:OK><19200>AT+FCLASS=1"
# ModemAnswerDataBeginCmd: "ATO\r<waitfor:CONNECT>"
#
We normally append the "@" symbol to the dial string so that
# the
modem will wait 5 seconds before attempting to connect
# and return result
codes that distinguish between no carrier
# and no answer. This makes it possible
to avoid problems with
# repeatedly dialing a number that doesn't have a fax
machine
# (kudos to Stuart Lynne for this trick.) #
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in
the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:
ATDT%s
# T
for tone dialing, @ for silence (Le
caractère @ est enlevé. Impératif)
#
# Other possible configuration stuff. The default strings are
# shown below.
Only those that are different from the defaults
# need to be included in the
configuration file.
#
#ModemResetCmds: "" #
stuff to do when modem is reset
#ModemAnswerCmd: ATA # use
this to answer phone
#ModemNoFlowCmd: AT+IFC=0,0
# disable flow control cmd
#
(Désactivation du contrôle
de flux, pour des anciens modem 28800, 33600 ou 56000,
#
essayez avec: #ModemNoFlowCmd:
AT&K0
# disable flow control cmd )
#ModemHardFlowCmd:
AT+IFC=2,2
# hardware flow control cmd
#
(Paramétrage du contrôle de flux matériel, pour des anciens modem 28800, 33600
ou 56000,
#
essayez avec: #ModemNoFlowCmd:
AT&K3
# disable flow control cmd ) ModemSoftFlowCmd:
AT+IFC=1,1
# software flow control cmd
#
(Paramétrage du contrôle de flux logiciel, pour des anciens modem 28800, 33600
ou 56000,
#
essayez avec: #ModemNoFlowCmd:
AT&K4
# disable flow control cmd )
#ModemNoAutoAnswerCmd:
ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that
we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0
ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0 # disable
command echo
#ModemVerboseResultsCmd: ATV1 # enable verbose command results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place
phone on hook (hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:
ATS8=2 # comma pause time is 2 seconds
#ModemRecvFillOrder: LSB2MSB # bit
order of received facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem
expects for transmit
#
Class1Cmd:
AT+FCLASS=1 # command to enter class 1
Class1TCFResponseDelay: 75 # 75ms delay
between recv TCF & response
Class1SendPPMDelay: 75 # 75ms delay before
sending PPM
Class1SendTCFDelay: 75 # 75ms delay between sending DCS & TCF
Class1TrainingRecovery: 1500 # 1.5sec delay after training failure
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead:
4 # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer: 40000 # 35+5secs
waiting for ident frames
Class1TCFMaxNonZero: 10 # max 10% of data may be
non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
| 
Retour
